Organoclay for Solventborne and Waterborne Coatings: CHINACOAT 2026, Booth 1.2F37
Which clay you buy comes down to two things: the system you’re running, and what you need the coating to do once it’s on the panel. We’ll have both ranges out at CHINACOAT 2026, Hall 1.2, Booth 1.2F37, 11 to 13 November, in Guangzhou. Come and talk grade selection, dispersion and performance in your own formulation.
### What makes solventborne and waterborne organoclay different?
Organoclay (organic bentonite, or organophilic bentonite) is bentonite modified with quaternary ammonium compounds. That modification makes the clay compatible with non-aqueous systems.

In solventborne coatings, solvent polarity decides how well the clay disperses and how well the gel structure develops. Grades that need activation take a polar activator, usually 3–5% of the pre-gel. Choose the wrong grade and extra mixing won’t rescue it.
Waterborne coatings use hydrophilic montmorillonite. It swells in water and forms a three-dimensional network, which suspends pigment and controls sag, with no polar activator and no separate pre-gel step.
Both systems chase the same things: pigment suspension, sag control, viscosity stability. They don’t get there with the same clay.
### Which grades are for solventborne coatings?
CP-10 and CP-180 cover low-polarity aliphatic and mineral spirit systems, with easy-dispersing options if you add powder straight to the mill. CP-20 is for low- to medium-polarity carriers, including medium- and long-oil alkyd and acrylic. CP-27 and CP-27A handle medium- to high-polarity solvents. CP-MPZ runs from non-polar through highly polar, which suits lines using several solvent blends. CP-EZ and CP-APA are easy-dispersing grades, so no separate pre-gel tank.
These end up in alkyd, acrylic, epoxy, polyurethane and chlorinated rubber coatings, plus marine anti-corrosion, automotive refinish and high-build industrial systems, where flow during application has to sit alongside structure afterwards.
### Which grades are for waterborne coatings?
CP-EW is the one for emulsion paints and general waterborne formulations. CP-EWS gives finer thixotropy, better transparency and easier dispersion than CP-EW, which is worth having in gloss and clear systems. CP-WBS and CP-EWB are refined and beneficiated grades for aqueous formulations, including putty, sealants and pigment slurries.
### What’s the right order for adding water-based clay?
Water first, at pH 7.0–8.0. Add the clay slowly under high-speed shear and disperse for 20–30 minutes. Additives, pigments, latex and let-down come after that.
Get the sequence wrong and you’ll see it in the batch: viscosity reads high, the structure isn’t there when the coating is applied. No polar activator is needed here, and these grades can take over part of an HEC or CMC package, which helps on formulation cost.
### What can visitors test at the booth?
Five checks. Dispersion in your own system, so bring a litre of your solvent blend, resin or let-down and we’ll run the grade in the carrier you actually use. Sag resistance and anti-settling against your current additive, using vertical draw-down plus accelerated storage. Viscosity at different shear rates, to see low-shear structure and high-shear flow. Transparency and fineness, for clear coats, gloss enamels and high-gloss decorative coatings. And addition level, where direct powder addition in solventborne coatings usually sits at 0.2–2% of total formulation weight, depending on the formulation.
### Can the same grade work in both systems?
No. Solventborne organoclay is modified for non-aqueous carriers and has to match the solvent polarity. Waterborne bentonite grades swell in water and need no polar activator. Use a grade in the wrong system and you get poor gel development or an unstable structure.
### Which grades suit epoxy, polyurethane or high-polarity solvents?
CP-27 and CP-27A for medium- to high-polarity systems, or CP-MPZ if you’re covering a wider spread of solvent blends. Where resin wetting is poor, as in some epoxy, polyester and short-oil alkyd systems, a surfactant alongside the clay is usually needed to develop the full structure.
### Do water-based grades need a polar activator?
No. Disperse in water at pH 7.0–8.0 under high shear for 20–30 minutes. An activator adds nothing in these aqueous systems and can disturb the gel.
### Who’s behind the booth?
We’ve worked with bentonite since 2000, source from our own ore and run 20,000 tonnes of annual organoclay capacity. Production is ISO 9001 certified, and we hold a national patent for a modified organic bentonite and its preparation method.
Export packaging comes in 25 kg bags or 600 kg big bags, at 15 MT per 20-foot FCL and 25.2 MT per 40-foot FCL. Delivery is 7–10 days after deposit, with a stated shelf life of 24 months.
### Where and when is the show?
CHINACOAT 2026, its 30th anniversary edition, runs 11–13 November 2026, Wednesday to Friday, in Area A of the China Import and Export Fair Complex in Guangzhou. You’ll find us in Hall 1.2, Booth 1.2F37. More than 1,280 exhibitors from 28 countries and regions had confirmed as of 18 September.
### How do I set up a meeting or request samples?
Email [email protected] or message +86-13185071071. Tell us your resin system, solvent or water base, and target film thickness. We’ll prepare samples that match and book a slot at Booth 1.2F37.
—
Bring your formulation details, or a sample of your carrier, for a 30-minute trial and a talk about sag control, pigment settling and viscosity stability. 11–13 November 2026 · Guangzhou · Hall 1.2 · Booth 1.2F37
Zhejiang Camp-Shinning New Material Co., Ltd. manufactures organophilic bentonite and organoclay rheology additives for coatings, inks, greases, adhesives and drilling fluids.